11
LTC1421/LTC1421-2.5
APPLICATIONS INFORMATION
U
U
U
is connected between REF (Pin 8) and the negative supply
and the trip point of Comparator 2 set to GND.
Soft Reset Generation
A soft reset that doesnt cycle the supply voltage can be
generated externally using Pin 11 (FB) as shown in Figure
9. For a 5V supply the FB pin is left floating to set the
internal supply monitor trip voltage to 4.65V. However, if
the FB pin is pulled to ground for more than 32祍 via a push
button or open-collector logic gate, the internal trip point
will go to 5.88V and the RESET pin will pull low. RESET will
remain low for 200ms after the FB pin is released. The
RESET signal will also be pulled low when the voltage at
the V
OUTLO
pin dips below 4.65V for more than 32祍.
When using a 3.3V supply, a 1k resistor must be con-
nected from the FB pin to V
CCLO
to set the internal trip point
to 2.90V.
sense resistor is greater than 50mV for more than 20祍.
When the circuit breaker trips, both N-channel MOSFETs
are quickly turned off, FAULT and PWRGD go low and
RESET is pulled low 32祍 later. FAULT can be connected
to a LED or a logic signal back to the host to indicate a faulty
board. The chip will remain in the tripped state until a
power-on reset is generated, or the power on V
CCHI
and
V
CCLO
is cycled. If the circuit breaker feature is not used,
short V
CCLO
to SETLO and V
CCHI
to SETHI.
If more than 20祍 of response time is needed to reject
supply noise, an external resistor and capacitor can be
added to the sense circuit as shown in Figure 10.
Figure 9. Generating a Soft Reset
Undervoltage Lockout
On power-up, an undervoltage lockout circuit prevents the
GATELO and GATEHI charge pumps from turning on until
V
CCLO
and V
CCHI
have both exceeded 2.45V.
Electronic Circuit Breaker
The LTC1421 features an electronic circuit breaker func-
tion that protects against short circuits or excessive cur-
rents on the supplies. By placing a sense resistor between
the supply input and set pin of either supply, the circuit
breaker will be tripped whenever the voltage across the
LTC1421
3.3V
5V
1/6 LS7404
OPEN
COLLECTOR
GND
32祍
200ms
FB
11
7
12
1421 F09
R1
1k
R1 USED FOR 3.3V
SUPPLY ONLY
RESET
RESET
FB
RESET
LOGIC
23
R
SENSE
C
F
Q1
22
R
F
21
20
V
CCLO
SETLO GATELO V
OUTLO
LTC1421
1421 F10
4
3
2
1
Figure 10. Short-Circuit Protection Circuit
Figure 11. AUXV
CC
Circuitry
GATE DRIVE
CIRCUITRY
10k
1礔
AUXV
CC
1421 F11
V
CCLO
24
LTC1421
23
GATELO GATEHI
21
17
Auxiliary V
CC
When a short circuit occurs on the board, it is possible to
draw enough current to cause the backplane supply
voltage to collapse. If the input supply voltage collapses to
a low enough voltage and the LTC1421 gate drive circuitry
is unable to shut off the N-channel pass transistors, the
system might freeze up in a permanent short condition.
To prevent this from occurring, the gate discharge cir-
cuitry inside the LTC1421 is powered from AUXV
CC
,
which is in turn powered from V
CCLO
through an internal
Schottky diode and current limiting resistor (Figure 11).
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
LTC1422CN8
IC CONTROLLER HOT SWAP 8-DIP
LTC1642CGN#TRPBF
IC CONTROLLER HOTSWAP ADJ 16SSOP
LTC1643AL-1CGN#PBF
IC CTRLR HOTSWAP PCI BUS 16SSOP
LTC1644CGN#TRPBF
IC CONTROLLER HOT SWAP 20-SSOP
LTC1645IS#TRPBF
IC CTRLR SEQ HOTSWAP DUAL 14SOIC
LTC1646IGN#TR
IC CNTRLR HOTSWAP PCIDUAL 16SSOP
LTC1647-1IS8#TRPBF
IC CONTROLLR HOTSWAP DUAL 8-SOIC
LTC1704EGN#TRPBF
IC REG DL BUCK/LINEAR 16SSOP
相关代理商/技术参数
LTC1421ISW-2.5#TR
功能描述:IC CONTROLLER HOTSWP 2.5V 24SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF)
LTC1421ISW-2.5#TRPBF
功能描述:IC CONTROLLER HOT SWAP 24-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件
LTC1422CN8
功能描述:IC CONTROLLER HOT SWAP 8-DIP RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件
LTC1422CN8#PBF
功能描述:IC CONTROLLER HOT SWAP 8-DIP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件
LTC1422CS8
功能描述:IC CONTROLLER HOT SWAP 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件
LTC1422CS8#PBF
功能描述:IC CONTROLLER HOT SWAP 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF)
LTC1422CS8#TR
功能描述:IC CONTROLLER HOTSWAP 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件
LTC1422CS8#TRPBF
功能描述:IC CONTROLLER HOT SWAP 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件